topics on Ericsson MKVI SGSNs with great details on HW, SW and Systems Configuration Overview Subscriber Commands Main KPIs AoB; 3. .. in use: gprs GGSN. THE ERICSSON SGSN-MME. -. Over a Decade of Erlang HSS. IP. Network. GGSN. SGSN. GSM: GSM+GPRS: W-CDMA: LTE: Ericsson+GGSN+and+SGSN+commands datasheet, cross reference, circuit and application notes in pdf format.
|Country:||Papua New Guinea|
|Published (Last):||7 May 2004|
|PDF File Size:||15.58 Mb|
|ePub File Size:||6.68 Mb|
|Price:||Free* [*Free Regsitration Required]|
In this example, you set security zones from zone ggsn and to zone sgsn.
Ggsj configuration mode, confirm your configuration by entering the show security policies command. It is an AP Application Processor board. It also performs authentication and charging functions.
Remember me on this computer. Views Read Edit View history.
If the output does not display the intended configuration, repeat the configuration instructions in this example to correct it. Some of them are mentioned below 1. The server can use the termination message to clear any related reservations made in the back-end balance management system. You set the application protocol to gprs-gtp-v0.
Log In Sign Up. Thus the packet will not be inspected by the GTP module. The response packet always sends to the request packet’s source address to the SPU. To quickly configure this example, copy the following commands, paste them into a text file, remove any line breaks, change any details necessary to match your network configuration, copy and paste the commands into the CLI at the  hierarchy level, and then enter commit from configuration mode.
Finally, you set the source port to and the destination port to The message flows are in general driven by the control-point asking for units and the server granting them. Finally, you set the default policy name to deny-all.
You set the action type to permit. To list down all parameters of configured values for different interfaces Pages using RFC magic links. PEB supplies the magazine with power, which is distributed from power connectors on the PEB front panel. This helps to calculate the remote SPU number in advance for the subsequent control message. The data transfer in GPRS is charged per megabytes for the traffic which is transferred, while in circuit switching for data communication, it is charged per minute for the time, the connection is alive.
The client is allowed to request units before the previous grant is completely used, in order to avoid suspending the subscriber session while talking to the server. Install the tunnel information into the predictable SPU. For quota management the client sends CCR to the conmands requesting cojmands and reporting consumption.
If you are done configuring the device, enter commit from configuration mode. Common Protocol Stacks Following are different protocol stacks for different interfaces.
Mailing List Archive: How to find GGSN Version?
You set the name of the match source address to ggsn-1 and the match destination address to sgsn In this example the client sends the request when 7 units of the 10 previously granted units have been used; and ask for 10 more units, which the server grants.
Ericsson GGSN commands datasheet & applicatoin notes – Datasheet Archive
During interrogation money is reserved from the user account. Event-based charging is typically used when units are not continuously consumed, e.
You set the application protocol to gprs-gtp-c. Thus it means that GGSN is router to a sub-network. SGSN Release 8 4. Thus the GTP tunnel is not established.
For instance, a user may pay for both online time and download bytes but has only a erlcsson account balance. Comands, the subscriber has ended the session, and the client sends a termination message to the server containing the last Used-Units. GGSN is responsible for IP address assignment and is the default router for the connected user equipment. Table of Contents 01 Introduction ………………………………….
GPRS technology is comprised of two network nodes: Each release provides a feature called Tool Box, which provides different commands for Troubleshooting, This can be resolved by installing the tunnel information to the correct SPU after the request and response packets are processed.
An ericeson credit control process uses events as charging mechanism. Over view of 2. From configuration mode, confirm your configuration by entering the show applications command.