BS EN ISO 14341 PDF

Classifications: EN ISO A; G 38 2 C1 3Si1; Weld Metal; EN ISO A; G 42 3 M21 3Si1; Weld Metal; EN ISO A; G 3Si1; Wire Electrode;. ISO – Download as PDF File .pdf), Text File .txt) or read online. BS en ISO Welding and Allied Processes. Flux and Gas Shielded. ISO. First edition. Welding consumables — Wire electrodes and deposits for gas shielded metal arc welding of non alloy and fine grain.

Author: Dujar Samulkis
Country: Oman
Language: English (Spanish)
Genre: Music
Published (Last): 22 October 2013
Pages: 49
PDF File Size: 17.76 Mb
ePub File Size: 6.9 Mb
ISBN: 142-6-87221-279-5
Downloads: 86682
Price: Free* [*Free Regsitration Required]
Uploader: Duzahn

iiso It is identical with ISO However, the direction of welding of layers shall be alternated. The work of preparing International Standards is normally carried out through ISO technical committees.

General principles ISOWelding consumables — Technical 14431 conditions for welding filler metals — Type of product, dimensions, tolerances and marking ISOWelding — Guidance on the measurement of preheating temperature, interpass temperature and preheat maintenance temperature ISO Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services.

Any analytical technique may be used, but in case of dispute, reference shall be made to established published methods.

BS ISO Welding consumables – MBA智库文档

The faster, easier way to work with standards. If below the indicated interpass temperature, the test assembly shall be reheated into interpass range. In the event that during preparation or after completion of any test, it is clearly determined that prescribed or proper procedures were not followed in preparing the weld test assembly or test specimen sor in conducting the tests, the test shall be considered invalid, without regard to whether the test was actually completed or whether the test results met, or failed to kso, the requirement.

For chemical analysis, retest need only be for those specific elements that failed to meet their test requirement. If 1,2 mm is not manufactured, closest size at settings as recommended by the manufacturer shall be used. Passes per layer Number of layers 1,2 1 to top 2 or 3 6 to 10 5.

  ANEMIA HEMOLITICA POR ANTICUERPOS FRIOS PDF

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.

The impact value shall be determined by the average of the three test specimens. It is the constant aim of BSI to improve the quality of our products and services.

BS EN ISO 14341:2011

Produits consommables pour le soudage. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.

The direction of welding used to complete a layer consisting of two passes shall not vary. The direction of welding for 41341 pass shall not vary.

Weld G3Si1 | Welding Consumables | Products & Solutions | ESAB

Consumable electrodes, Welding electrodes, Filler metal, Arc-welding equipment, Wires, Gas-shielded welding, Gas metal-arc welding, Welding equipment, Unalloyed steels, Steels, Classification systems, Yield strength, Elongation, Tensile strength, Impact strength, Chemical composition, Designations.

The lowest and highest values obtained shall be disregarded. Endorsement notice Sb text of ISO The ratio of yield to tensile strength of weld metal is generally higher than that of parent metal. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. We use cookies to make our isk easier to use and to better understand your needs.

If, after any pass, this interpass temperature is exceeded, the test assembly shall be cooled in air to a temperature within that range. Except as permitted under the Iwo, Designs and Patents Act no extract may be reproduced, stored in a ba system or transmitted in any form or by any means — electronic, photocopying, recording or otherwise — without prior written permission from BSI.

  BAROTRAUMA TELINGA PDF

This document supersedes EN We operate in countries and are the number one certification body in the UK and US. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. This is mainly due to the differences in welding procedures — including electrode size, width of weave, welding position and material composition. 143341

The two designation approaches include additional designators for some other classification requirements, but not all, as will be clear from the following sections. Customers who bought this product also bought BS EN Specimens for the retest may be eh from the original test assembly or from a new test assembly.

You may find similar items within these categories by selecting from the choices below:. ISO Welding — Studs and ceramic ferrules for arc stud welding. The interpass temperature shall be measured using temperature indicator crayons, surface thermometers or thermocouples see ISO Specifications and test methods BS EN Contact the Information Centre.

A list of organizations represented on this committee can be obtained on request to its secretary. One wire electrode can be tested and classified with different shielding gases.

Take the smart route to manage medical device compliance. ISO shall not be held responsible for identifying any or all such patent rights. Search all products by. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. A wire bd shall be classified according to its chemical composition as in Table 3A or Table 3B.